If you have faced problems related to wifi coverage, then you are not alone. To get rid of this, people always buy range extenders. Sometimes, the extenders also start to give off problems. This is when many users search that their wavlink wifi I not working.
Although wavlink AC1200 is among best of the extenders, it can also experience problems at times. This happens when the device has been working for months and months, without rest in between. Continuous use of any device will affect its capability to work properly. One may experience, no internet, abrupt drop in speed or not enough range. But getting rid of all of these is quite easy.
Below are some detailed steps which can help the user in configuring wavlink AC1200 setup easily.
First Things First: Basic Wavlink AC1200 Setup
Most folks make mistakes in the very beginning. If you follow the steps given here, configuring AC1200 setup would be easy:
- Plug the extender into a wall outlet near your router. Don’t shove it in the far room yet. Setup works better when the extender is in close range to your main router.
- Wait for the power light to come on. Should be solid. If it’s not, unplug and re-plug. Sometimes outlets are loose.
- Connect your laptop or phone to the extender’s default WiFi network. It usually shows up as “Wavlink-N” or “Wavlink-AC”. No internet at this stage, just local connection.
- Type default IP address in the browser. For Wavlink it’s often “192.168.10.1” or “wifi.wavlink.com”. If one doesn’t load, try the other.
- You’ll hit the login page. Default user is “admin” and password is “admin” unless you changed it before.
- Once inside, choose “Repeater Mode” or “Extender Mode.” That’s the option that makes it repeat your existing WiFi.
- Pick your home WiFi network from the scan list. Enter your WiFi password carefully. One wrong letter and you’ll be wondering why the wavlink extender not working again.
- Save settings. The extender will reboot. Remember to keep the extender halfway between the dead zone and router.
That’s the clean install. If you stopped here and it works, good. If not, read on.
Common Problems and Quick Fixes
There is always a chance that the device may not work properly, even if the setup has been installed correctly. This is the time when users scour the net with question like “wavlink extender not working”. Refer the below steps, if you facing the same
- No Internet After Setup -this usually happens when wrong password has been entered. Just reset the extender and it will work fine.
- Inaccessible Login Page - if the default IP doesn’t work, try the official website. Wifi.wavlink.com. you can try clearing browsers cache as well. But first of all, check the device has been connected to the extenders wifi.
- Sudden Drop Of Connection - if the extender is not at an optimal distance from the router this is most likely to happen.
- Bands Selection – many devices cant access 5GHz, try switching to 2.4GHz. it’s a bit slower but more stable. If you have an AC1200, no need to worry. It supports both the ranges.
- LED Signals – if LED is showing green or blue light, signal strength is good. If its flashing or showing red color, the connection is weak.
Step-By-Step Fix Guide When Extender Refuses to Work
This section will give something more advanced. There is a rare chance that the above steps doesn’t work. And you may still searching “wavlink extender not working”. Let’s take it further:
- Reset
- If nothing works, then reset wavlink AC1200 setup. Press the button given on the back of the device for a few seconds & it will be done.
- Regular Firmware Update
- keep an eye out for updates regarding the firmware. On official wavlink site, there is regular updatation of new firmware software. They are not just for security but also improve performance.
- Check IP Address
- as the extender just repeats the signal produced by the router. Sometimes this creates hindrance in the working of extender because both are using same IP. Just log in, and change the default IP 192.168.10.1 to another address.
- Switch Mode
- Multiple modes like:- Repeater, Router, AP (Access Point- Wired Connection) can help in different situations If repeater isn’t stable, try AP mode. For AP mode you’ll need to connect the extender to the router using a LAN cable. Solid fix for many.
- Power Cycle Everything
- Sounds silly but works. Turn off the main router, extender, and device. Wait 1-2 minutes. Power on router, wait for it to fully boot, then power extender, then device. Many times this clears temporary glitches.
- Check for Double NAT Issues
- If you have ISP modem + your own router + extender, sometimes “double NAT” slows or breaks things. In that case, switch extender to AP mode instead of Repeater.
- Factory Reset Router if Needed
- Rare but sometimes the router itself has bad settings that prevent extender from working. If all else fails, reset router and redo both router and Wavlink AC1200 setup from scratch.
Tips to Keep the Wavlink AC1200 Running Smooth
Once you finally get it working, you don’t want to repeat the nightmare every few days. A few practical habits go a long way:
- Don’t move the extender once you find a good spot. Keep it in line of sight of the router if possible.
- Avoid plugging it behind big TVs or inside cabinets. Signals get blocked.
- Reboot once in a while. Just unplug and re-plug.
- If you change your WiFi password on the router, remember you must also update it on the extender. Otherwise, you’ll again think the wavlink extender not working.
- Keep firmware updated every few months.
For large houses, one extender might not be enough. Sometimes it’s not about the extender failing but about expecting too much coverage.
Wrapping Up
When your wavlink extender is not working, first thing that comes to mind is that it has some sort of fault. But that’s not the case always. If you follow the steps given here, then configuring wavlink AC1200 setup is easy as a free throw. Just- connect, configure, check for updates and place it at an ideal distance. You’ll see that all the deads zones of your house/workspace are vanished.
Comments